manual for delfship, Free
› DELFTship forum › Hull modeling › manual for delfship, Free
- This topic has 7 replies, 3 voices, and was last updated 10 years, 7 months ago by
Ben.
-
AuthorPosts
-
-
May 2, 2012 at 14:06 #35943
Ben
ParticipantHi, my name is Ben and i am a few issues with editing my drawing, i am designing a power boat so want hard chines and folded edges, but i can only get rounded ones :angry: reading the manual it says to select the lines and edit=>edge=>crease, problem is edit function is either delete or un/re-do…
im very new to this and trying to search the forum has not working for me…
any help much appreciated
Attachments: -
May 3, 2012 at 06:56 #35944
Sergio Diaz-Ibieta
ParticipantHello Ben,
Your hull is quite irregular in the bow and chines and it still needs a lot of work. I don’t know what kind of work boat you are aiming, but I tried to play a little bit with the crease edges and clean some edges to check if I found something useful. Have a look.
In any case, if you want to define knuckle lines or chines, you just have to select the edges and turn them into crease edges.PS: Try downloading power boats from delftship database. There are quite a few very interesting for your work.
Hope this is of some help.
Regards,
Sergio -
May 3, 2012 at 10:40 #35945
Ben
Participantcool, cheers for that
this is what i am desgining my boat for: http://www.youtube.com/watch?v=qVCkcDClamQ&feature=player_embedded powered by jetski engine the reason for the delta recessed is because when you go over shingle the stones get jammed into the grill reducing the units performance.
Attachments: -
May 3, 2012 at 13:35 #35946
Ben
ParticipantHi again, am i missing something or is the PDF manual not the same for the free version of delfship? reading thru the 6-delfship and 8-hull modeling they don’t seam to be the same as the program i am using.
im trying to create layers so i can have individual panels for a cutting list.
regards Ben
-
May 4, 2012 at 02:26 #35949
raf pali
Participantim trying to create layers so i can have individual panels for a cutting list.
regards Ben
Click on the new layer command found on the layer section on the toolbar… the one in the middle with a little green plus sign on it.
-
May 4, 2012 at 06:45 #35951
Sergio Diaz-Ibieta
ParticipantHi Ben,
Nice little boat to run over the river stones and rocks…
Find attached a next step for your boat.Regards,
Sergio -
August 11, 2012 at 00:03 #36157
Ben
Participantstarted build my wee boat :woohoo:
-
August 11, 2012 at 00:16 #36160
Ben
Participantmore
open to comment, i think the bow entry is a little steep, im going to tow it behind another boat to see how it cuts thru the waves etc.
Attachments:
-
-
AuthorPosts
- You must be logged in to reply to this topic.
Your account
Recent Topics
-
Modeling the 1907 U.S. Brigantine Galilee
by
Terrance Egolf
1 month ago -
install problems
by
tcurdt
1 month, 1 week ago -
VCG and GM of Smit Rotterdam
by
DuncanH
1 month, 1 week ago -
Revision/save history?
by
Jamie
1 month, 1 week ago -
Create deck plane as the intections at z=xxx with the hull
by
Pidgee
3 months, 2 weeks ago -
Cylinder through curved deck
by
RuudN
3 months, 2 weeks ago -
Exporting table of offsets
by
Peter Mitchell
4 months, 2 weeks ago -
Modelling a flat bottom chine tug hull (WWII TID)
by
Paul
4 months, 3 weeks ago -
Correct Hull Shape from Existing Lines Plan
by
patmat41959
4 months, 4 weeks ago -
Deck Camber
by
patmat41959
4 months, 4 weeks ago