AutoCAD & FreeShip
› DELFTship forum › Hull modeling › AutoCAD & FreeShip
- This topic has 8 replies, 3 voices, and was last updated 10 years, 2 months ago by
iosif gross.
-
AuthorPosts
-
-
March 4, 2011 at 04:52 #34721
iosif gross
ParticipantI have imported chines from AutoCAD (single chine)
The Sheer and Centerline are same, but the chine ends in different point than the imported xyz (in FreeShip it ends at the Sheer and Centerline end/stem)
Have some solution?0
0.000 0.000 0.000
0.800 0.000 -0.147
1.600 0.000 -0.181
2.400 0.000 -0.157
2.800 0.000 -0.118
2.923 0.000 -0.083
2.982 0.000 -0.045
3.023 0.000 0.000
3.057 0.000 0.060
3.200 0.000 0.3970.000 0.106 0.046
0.800 0.110 -0.098
1.600 0.114 -0.126
2.400 0.095 -0.068
2.800 0.053 0.000
3.057 0.000 0.0600.000 0.142 0.333
0.800 0.146 0.349
1.600 0.150 0.365
2.400 0.131 0.381
2.800 0.089 0.389
3.200 0.000 0.397EOF
Best regards
Iosif -
March 9, 2011 at 05:01 #34725
iosif gross
ParticipantI have added jpg that compares the drawings
Attachments: -
March 14, 2011 at 12:49 #34731
iosif gross
ParticipantI undestand that can’t expect to get answer for every question regarding a free software.
Can I get answer to the bellow question?DELFTship can import DXF files. They will be drawn in DELFTship exactly as in AutoCad where they was generated or will be changed as the xyz imported cordinates to FreeShip as I have shown in my previous posts
I WILL APPRECIATE EVERY ANSWER THAT WILL CLARIFY MY QUESTION
-
September 29, 2012 at 03:51 #36279
iosif gross
ParticipantBetter later than never.
DELFTship is drawing exactly as it was in AutoCad. 🙂 🙂 🙂
The mistake was mine in the xyz file 🙁Best regards
Iosif -
October 1, 2012 at 20:57 #36282
Jesus Cruz
ParticipantI use the import chines and curves feature very often, and I allways have to do “minor” adjustments once i get tha model, in my opinion is very fats and gives a good accurancy, so as I said, I used very often with very good results.
-
October 2, 2012 at 05:16 #36284
iosif gross
ParticipantMy problem was 18 months ago and because of my work I was out from the subject. Just recently I begin again with the old model and I find out that the problem was my xyz wrong coordinates. So FreeShip made the drawing according to what I have asked.
Now the drawings are similar, with small corrections. -
March 17, 2013 at 02:43 #36612
iosif gross
ParticipantAgain problem with importing xyz file. I am sure I am making some mistake but I don’t understand what:
0
0.000 0.000 0.000
0.550 0.000 0.000
1.100 0.000 0.000
1.650 0.000 0.011
2.200 0.000 0.113
2.750 0.000 0.432
2.970 0.000 0.6050.000 0.660 0.132
0.550 0.660 0.132
1.100 0.651 0.146
1.650 0.589 0.197
2.200 0.400 0.297
2.750 0.000 0.4320.000 0.720 0.495
0.550 0.720 0.515
1.100 0.720 0.536
1.650 0.720 0.556
2.200 0.658 0.577
2.750 0.385 0.597
2.900 0.212 0.602
2.970 0.000 0.605EOF
According to the xyz file, the chine should end at x=2.75 but it ends at 2.97
2.75 is the place when the chine line should connect to the keel linePLEASE HELP
Iosif
-
March 18, 2013 at 11:58 #36613
Marven
KeymasterYou should only enter the points of the chine from the stern to the bow until the chine meets another curve. so in your case the point where the keel meets the bow (at 2.750 0.000 0.432) should be the end point of the curve.
This results in 6 points for the keel and chine curves and 8 points for the deck line. When the curves are imported the software will automatically ensure that the number of points on each imported curve is equal to the other curves. To avoid loss of accuracy I’d suggest the make this number equal to the number of points on the curve with the largest number. In your case that would be 8.The resulting file should look like this:
0
0.000 0.000 0.000
0.550 0.000 0.000
1.100 0.000 0.000
1.650 0.000 0.011
2.200 0.000 0.113
2.750 0.000 0.4320.000 0.660 0.132
0.550 0.660 0.132
1.100 0.651 0.146
1.650 0.589 0.197
2.200 0.400 0.297
2.750 0.000 0.4320.000 0.720 0.495
0.550 0.720 0.515
1.100 0.720 0.536
1.650 0.720 0.556
2.200 0.658 0.577
2.750 0.385 0.597
2.900 0.212 0.602
2.970 0.000 0.605EOF
-
March 20, 2013 at 04:20 #36616
iosif gross
ParticipantHi Marven
Thank you for the advice. I am in a trip so I will do it at the end of the week and report the results
Iosif
-
-
AuthorPosts
- You must be logged in to reply to this topic.
Your account
Recent Topics
-
install problems
by
tcurdt
2 weeks, 1 day ago -
Import lines plan (DXF) back into D/S?
by
Paul
3 weeks, 3 days ago -
Remove Background Image?
by
Paul
3 weeks, 3 days ago -
Size of background image
by
Axel
1 month, 1 week ago -
Stepped hull and Spray Rails
by
Tahoesteam1
1 month, 2 weeks ago -
Lines plan disabled
by
Martin
2 months, 1 week ago -
Modeling the 1907 U.S. Brigantine Galilee
by
Terrance Egolf
3 months, 2 weeks ago -
VCG and GM of Smit Rotterdam
by
DuncanH
3 months, 2 weeks ago -
Revision/save history?
by
Jamie
3 months, 3 weeks ago -
Create deck plane as the intections at z=xxx with the hull
by
Pidgee
5 months, 4 weeks ago